You may also like to see farmhouse dining table. These DIY patio table plans will show you how to easily build an attractive wooden outdoor table that has ‘X’ brace legs and a herringbone top design. Here we have a high-end design table with a low-end price tag. Tutorial: thefrugalhomemaker Frugal DIY Outdoor Table Image via: thefrugalhomemaker 4. When you’re finished with your project, you’ll have built a beautiful farmhouse table without spending a lot of money. Like other plans we are sharing with you, this table is big enough to seat four to six people, and you can use cushioned dining or patio chairs to add comfort to your space. In fact, these plans show you how to build your table using 17 2×4 boards. Frugal DIY Outdoor TableĪre you looking for a frugal option for your outdoor furniture? We suggest you look no further than this frugal diy outdoor table, which you can build for less than $60. Tutorial: justagirlandherblog Farmhouse-Style Picnic Table Image via: justagirlandherblog 3. In addition, every mealtime feels like a picnic in your own backyard. There’s enough room to seat several people at your table, plus it adds a touch of coziness to your country-style exterior. It’s recommended to finish the job with General Finish’s Outdoor Oil, as this oil enhances the beauty of the wood, and it holds up well outside. You’re going to build this picnic table from scratch using lumber, screws and several tools, and it’s going to include two benches and the table itself. If you’re looking for a DIY outdoor table with a country vibe to it, we suggest you consider a farmhouse-style picnic table like this. Tutorial: cravingsomecreativity DIY Outdoor Dining Table Image via: cravingsomecreativity 2. While these plans are for repurposing an old dining table, you do have the option of building your table from scratch. You can even add a cross-X pattern or granite to the tabletop to give it a unique look.įinish it off with wooden dining chairs, which you can adorn with cushions for style and comfort. The table is large enough to sit four to six people comfortably. Finish the table as desired with primer and paint, wood stain, or clear polyurethane varnish.Can you imagine an evening of dining outside in the nice weather? With these plans, you can build a DIY dining table that fits on your porch.Hammer a furniture glide onto the bottom end of each table leg.Center the table legs on the top, then drive 5/8-inch screws through the double washers and into the underside of the tabletop.Set the tabletop upside down on a padded workbench, then place the bottom portion of the table on top with legs sticking straight up.Use a 5/8-inch screw to fasten a steel double washer to each recess.Position the recesses close to each table leg. Drill four 1/8-inch-deep recesses into the top edges of the aprons with a ¾-inch spade bit.Repeat to attach the remaining three aprons. Then fasten the apron to the table legs with 1½-inch pocket screws. Slip a ¼-inch-thick spacer block beneath each end of the apron to create a reveal along the leg.Use a cordless drill and pocket-hole jig to drill two screw-pocket holes into each end of all four aprons.Use the router with 1/8-inch-radius rounding-over bit to rout around the top of the tabletop.Use the random-orbit sander to sand both sides of the tabletop. Remove the bar clamps from the tabletop.Next, use a router equipped with a 1/8-inch-radius rounding-over bit to ease the sharp corner where the two tapered leg surfaces meet.Sand smooth all four sides of each table leg with a random-orbit sander fitted with 120-grit abrasive.Repeat the previous two steps to cut two tapers into each of the remaining three 2×2 table legs.Lock down the clamp and cut a second taper into the leg. Unlock the toggle clamp and rotate the leg 90 degrees.Turn on the table saw and slide the jig past the blade to cut a taper into the 2×2 table leg. Set the 2×2 into the jig and lock it down with the toggle clamp.Screw a toggle clamp to the top of the jig. Adjust the taper to start 8 inches down from the top of the legs. Cut a notched taper into the 1×4 to permit removing ½ inch from the 2×2 legs. Make a tapering jig out of ¾-inch plywood and a 1×4.Wipe off the excess glue with a damp cloth.Use two bar clamps to clamp together the four boards to form the tabletop.Apply carpenter’s glue to the edges of the boards, then evenly spread the glue with a narrow stick.Use a table saw to rip off the edges of the 5/4-by-6-inch fir decking, creating four square-edge boards.Cut the fir table parts to length with a miter saw.4 to 6 hours Building a simple side table
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |